A wall can feel dry to the touch in a day while the studs and plates behind it stay wet enough to feed mold. One call to Water Heater Repairer connects you with an independent drying specialist near Clovis who meters, maps and documents the structure until it is truly dry.
Structural drying is controlled psychrometrics, not a few box fans pointed at a wet carpet.
Calls go to independent local drying contractors who carry their own license and insurance. Plenty hold IICRC water restoration training; ask to see it at the door.
Water keeps wicking up drywall by the hour, so we look for crews with drying gear already on the truck. Arrival is often within the hour depending on location and demand.
Before the first fan spins, the contractor writes up the drying plan, the equipment count and the rate structure. No surprise line items for equipment days you never agreed to.
Pin and pinless moisture meters, thermo-hygrometers and thermal imaging cameras are the core kit. With them, the drying job runs on recorded numbers instead of hunches.
A familiar call goes like this: the leak got fixed, the floor feels fine, and yet the room smells musty a week later. Almost every time, the moisture is still sitting in the bottom plate, inside the wall cavity, or in the subfloor beneath the pad. Finding and pulling out that hidden moisture is the whole job of a structural drying contractor.
We also hear from people worried about the noise and the power bill. Most setups run a handful of air movers and a dehumidifier or two nonstop, so a good contractor checks which circuits can carry the load. Running it right for a few days costs far less than replacing cupped flooring, delaminated cabinets or moldy drywall later.
Every job opens with a moisture map and closes only when all readings reach target.
The contractor takes a dry standard reading from unaffected drywall, trim and flooring in the same building. That figure, near the material's equilibrium moisture content, sets the goal each wet spot has to hit.
Low-grain refrigerant units strip moisture from the air down to low grains per pound. In cold basements or with hardwood and plaster, a desiccant unit keeps drying where refrigerant coils fall off.
Axial fans move big volumes over open floors; centrifugal units aim tight, fast air along wall bases and under cabinets. Every unit goes where the moisture map says, not where it fits.
Instead of tearing out drywall, many contractors pull the baseboard and drill small holes into the cavity behind it. An injection manifold feeds dry air into each stud bay, and the baseboard covers the holes once it is reset.
Wet hardwood cups as the bottoms of the boards swell faster than the tops. Sealed drying mats or panels draw moisture up through the wood with steady suction.
In a closed chamber, plastic sheeting walls off the wet area so equipment conditions a smaller volume of air. It dries faster and keeps the noise and electrical load out of the rooms you are living in.
This is how a well-run drying job moves from day one to sign-off.
We ask about the water source, how long it sat, and which floors and rooms got wet. Those answers tell us whether you need drying only or extraction first, and we route the right contractor.
The pro shows up carrying meters, a thermal imager and a starting set of dehumidifiers and fans. Thermal imaging traces how far water has wicked up walls before anything gets moved.
The written scope lists the evaporation class, the drying goals, how many units, the likely timeline and the rate structure. Nothing runs until you approve it.
Daily visits record readings, shift equipment and remove units as each area hits target. You keep the final dated drying log for your adjuster and records.
Fans by themselves just stir humid air around; they do not take the water out. As relative humidity rises, vapor pressure in the room catches up to the wet material and drying stalls. Without dehumidification controlling grains per pound, the framing can stay wet for weeks.
| Evaporation class | What it usually means |
|---|---|
| Class 1 | Small area, little absorbed water |
| Class 2 | A full room wet, with water wicked up walls under two feet |
| Class 3 | Overhead water that soaked ceilings, insulation and walls |
| Class 4 | Hardwood, plaster, concrete or deep pockets of bound water |
Have an independent drying pro near Clovis take readings today.
Our dishwasher leaked overnight and the kitchen floor looked fine by lunch. The pro compared the oak to a dry board in the hall, found it far too wet, and sealed drying panels over it. It ran five days, and the boards stayed flat.
The insurance adjuster tried to knock two days of equipment off the claim. I sent the daily log with moisture readings for every wall, and the full invoice was approved. Having those numbers made the conversation short.
I run a small office, and a toilet supply line flooded three rooms on a Friday. Instead of tearing out walls, the crew pulled baseboards and fed dry air into the cavities through small holes. They tented off the wet rooms, so the front office stayed open.
Our basement got wet after a water heater let go, and we ran fans for a week. The smell would not go away, so we called and the pro scanned the walls with a thermal camera. Moisture had climbed nearly two feet behind the paneling, and a desiccant dehumidifier plus daily readings finished the job.
Most Class 2 losses reach their drying goals in three to five days. Dense materials like hardwood, plaster or concrete often run longer since the water sits deeper. Daily readings, not the calendar, decide when equipment comes out.
They compare readings in the wet area to a dry standard taken from unaffected drywall in the same building. When the wet readings match that baseline, the area has reached its goal.
Often they do not. With clean water and uninsulated cavities, injection drying through small holes behind the baseboard can save the drywall. Wet insulation, contaminated water or mold growth usually means a flood cut.
Shutting them off at night lets the air get damp again and undoes part of the progress. A closed chamber can keep the noise and electrical load inside the wet rooms, so ask about one.
LGR dehumidifiers run on chilled coils and shine in normal room temperatures. A desiccant unit pulls moisture with an absorbent wheel and keeps drying in cold basements or on dense materials.
Getting drying mats on quickly gives the boards their best shot at flattening out. Slight cupping often eases as moisture evens out, which is why pros advise waiting before sanding.
We route drying contractors to homes and businesses across Clovis and nearby suburbs, including 88101 88102. Downtown condo or edge-of-town split-level, the method does not change: meter it, map it, dry it and log it.
Plaster walls and old-growth hardwood hold water longer and usually need desiccant drying.
Shared walls mean water travels sideways, so the moisture map often extends next door.
Slab homes and finished basements around Clovis get the same readings-first approach.
Supply line, water heater, upstairs tub: whatever the source, earlier calls mean less wicking. Each hour wet lets moisture climb walls and soak further into framing.
Call +1-877-637-9008
